Protective Coatings

Bio Coat SUP250 Part A
BioCoat-SUP250-B
Product Information

BioCoat SUP205 is a bio-based, two-component, water-based, VOC-free polyurethane coating that combines ease of use with high bonding performance on concrete, ceramic, wood, and metal substrates. BioCoat SUP205 contains zero microplastics and has no odor. BioCoat® SUP205 provides a durable and long-lasting coating that has best-in-class abrasion, UV and corrosion resistance, and resistance to mold, bacteria, and viruses.

Advantages

  • 25% Bio-Based
  • Low Odor
  • Microbial Resistant
  • Mold Resistant
  • Fungal Resistant
  • Low VOC
  • Contributes to LEED Credits
Application

Surface Preparation: 

  1. For high strength structural coatings, remove surface contaminants such as paint, oxide films, oils, dust, mold release agents and all other surface contaminants.
  2. Use gloves to minimize skin contact.

Mixing Instructions for a 1-gallon Kit:

  1. Mix Part A well prior to use. Use a paint stick or a drill mixer.
  2. Add all of Part B to Part A.
  3. Mix 5 minutes using a paint stick or drill mixer.
  4. Add 28 fluid ounces of water to Part A.
  5. Mix for 5 minutes using a paint stick or drill mixer.
  6. Add the entire content of the Accelerator to Part A if a faster dry is desired.
  7. When the Accelerator is added the dry time of the coating is approximately 10 –
    12 hours. When the Accelerator is not added, the dry time of the coating is
    approximately 20 – 24 hours.
  8. Mix for 5 minutes using a paint stick or drill mixer.
  9. Apply with brush, roller or sprayer to substrate.
  10. Application thickness: 3-4 dry mills (6 – 8 wet mills
  11. Pot life: Approximately 1 hour
  12. Dry Time: 10 – 12 hours under ambient conditions (70F, 30% humidity). Dry
    time will take longer under cooler ambient temperatures and/or higher humidity.
  13. Full Cure Time: 5 days
Learn More

Contact a BioBond Expert at [email protected]

BioCoat Sup250 Accelerator
Product Information

BioCoat SUP205 Accelerator speeds up drying times for BioCoat SUP205. The Accelerator contains zero microplastics and has no odor. It speeds up the process while allowing the BioCoat SUP205 to be the same durable and long-lasting coating. The Accelerator will speed up the coating dry time. 

Advantages

  • 25% Bio-Based
  • Speeds up drying times of BioCoat SUP250.
Application

 Surface Preparation: 

  1. For high strength structural coatings, remove surface contaminants such as paint, oxide films, oils, dust, mold release agents and all other surface contaminants.
  2. Use gloves to minimize skin contact.

Mixing Instructions for a 1-gallon Kit:

  1. Mix Part A well prior to use. Use a paint stick or a drill mixer.
  2. Add all of Part B to Part A.
  3. Mix 5 minutes using a paint stick or drill mixer.
  4. Add 28 fluid ounces of water to Part A.
  5. Mix for 5 minutes using a paint stick or drill mixer.
  6. Add the entire content of the Accelerator to Part A if a faster dry is desired.
  7. When the Accelerator is added the dry time of the coating is approximately 10 –
    12 hours. When the Accelerator is not added, the dry time of the coating is
    approximately 20 – 24 hours.
  8. Mix for 5 minutes using a paint stick or drill mixer.
  9. Apply with brush, roller or sprayer to substrate.
  10. Application thickness: 3-4 dry mills (6 – 8 wet mills
  11. Pot life: Approximately 1 hour
  12. Dry Time: 10 – 12 hours under ambient conditions (70F, 30% humidity). Dry
    time will take longer under cooler ambient temperatures and/or higher humidity.
  13. Full Cure Time: 5 days
Learn More

Contact a BioBond Expert at [email protected]

BioCoat SWaE250 Part A
BioCoat SWaE250 Part B
Product Information

The BioCoat SWaE250 is a 63% solids, water-based, bio-based two-part epoxy primer. It bonds to concrete extremely well and is used as a Primer coat or Main Coat for concrete floor applications. It dries to the touch in approximately 2 hours, allowing you to quickly move to the next step. BioCoat SWaE250 is specially formulated to bond well with other BioBond epoxies and polyurethanes to ensure a strong
bonding system that provides the ultimate in floor protection.

Advantages

  • 25% Bio-Based
  • Low Odor
  • Water-Reducible up to 20%
  • Low Viscosity
  • > 60% solids
  • Low VOC
  • Contributes to LEED Credits
Application

Mixing Instructions

  1. Mix Part B well prior to use. Use a paint stick and be sure to re-mix
    the solids that have settled out at the bottom of the can. Be sure to
    scrape the solids off the bottom and sides of the can with the
    paint stick and mix them back into the solution. This process will
    take about 5 minutes.

  2. Add all of Part B to Part A.

  3. Mix 5 minutes using a paint stick or drill mixer.

  4. Add 20 fluid ounces of water to the mixture in Part A

  5. Mix for 5 minutes using a paint stick or drill mixer.

  6. Apply with brush, roller or sprayer to substrate.

  7. Application thickness: 3-4 dry mills (6 – 7 wet mills)

  8. Pot life: Approximately 1 hour

  9. Dry Time: 3 – 4 hours under ambient conditions (70F, 30%
    humidity). Dry time will take longer under cooler ambient
    temperatures and/or higher humidity.

  10. The next coat (topcoat or main coat) can be applied once the
    C25EPWB is dry.

  11. Full Cure Time: 5 days

Learn More

Contact a BioBond Expert at [email protected]

BioCoat SSoE250 Part A
BioCoat SSoE250 Part B
Description

BioCoat SSoE250 is a 100% solids, bio-based two-part epoxy floor coating. It bonds to concrete extremely well and is
used to create a high-build epoxy coating. It dries to the touch in approximately 8 to 10 hours. BioCoat SSoE250 be applied thick enough to level uneven surfaces, creating a seamless floor coating.

Advantages

  • 30% Bio-Based
  • Solids Based
  • Low Odor
  • High Viscosity
  • Low VOC
  • Contributes to LEED Credits
Application

Mixing Instructions for the 1-gallon Kit:

 

  1. Mix Part B well prior to use. Use a paint stick or a drill mixer. Mix SLOWLY and GENTLY to minimize entrainment of air bubbles.
  2. Add all of Part B to Part A.
  3. Mix 5 minutes using a paint stick. Mix SLOWLY and GENTLY to
    minimize entrainment of air bubbles.
  4. Apply with brush, roller or sprayer to substrate.
  5. Application thickness (flooring): 5 – 50 dry mils (5 – 50 wet mils)
    (depending on the surface roughness and unevenness. Smooth
    floors will require less thickness while rougher floors will require a
    thicker coating)
  6. Pot life: Approximately 1 hour
  7. Dry Time: 8 – 10 hours under ambient conditions (70F, 30%
    humidity). Dry time will take longer under cooler ambient
    temperatures and/or higher humidity.
  8. The next coat (topcoat) can be applied once the C30EPHB is dry.
  9. Full Cure Time: 5 days
Learn More

Contact a BioBond Expert at [email protected]